12a-YF Duracool cylinder 5.44 kg - Replacement HFO-1234yf (11.34 kg eq.)

Duracool 12a-YF: The Environmentally Friendly Hydrocarbon Refrigerant Replacing HFO-1234yf

The air conditioning sector, particularly the automotive sector, is facing increasingly stringent regulatory and environmental constraints regarding the use of fluorinated gases. The 12a-YF Duracool is the technical and ecological answer to this problem. This refrigerant is specially formulated with natural hydrocarbons to directly replace HFO-1234yf gas, which is widely used in recent vehicles. This large format cylinder of 5.44 kg net offers a capacity equivalent to 11.34 kg of HFO-1234yf, allowing professionals to benefit from a solution that is both economical and much more efficient. Our commitment is to provide workshops and refrigeration specialists with a reliable, powerful and environmentally friendly alternative.

Superior Thermal Performance and Energy Efficiency

The major advantage of the 12a-YF Duracool lies in its thermodynamic efficiency. This natural gas is known for its ability to transport and transfer heat more efficiently than traditional fluorinated fluids.

• Reduced load: Due to its properties, the amount of Duracool required to achieve the required refrigeration performance is considerably lower than that of HFO-1234yf. This means that 5.44 kg of Duracool 12a-YF is enough to replace more than twice their weight in fluorinated gas (11.34 kg).

• Fuel Economy: The compressor of the air conditioning system (Air Conditioning Auto or other) works less to obtain the same coolness. This efficiency translates into lower compressor energy consumption , and consequently a slight fuel saving for the vehicle.

• Low Discharge Temperature: The 12a-YF Duracool also allows for a lower compressor discharge temperature, increasing the life of the air conditioning system.

Environmental Advantage & Compliance

The choice of a refrigerant gas is no longer just a question of performance, but of environmental impact.

• Global Warming Potential (GWP): The 12a-YF Duracool has an extremely low GWP (close to 3), aligning with the European Union's objectives to reduce the climate impact of HFCs and HFOs. For comparison, HFO-1234yf has a much higher GWP.

• Non-Ozone Depletion (ODP): Its natural composition guarantees zero ODP. It is a 100% ecological solution, not contributing to the destruction of the ozone layer.

• Regulatory Status: As a hydrocarbon (HC) gas, Duracool 12a-YF is not subject to restrictive F-Gas quotas.

Optimal Compatibility and Ease of Transition

The integration of this substitute gas into existing systems is facilitated by its compatibility with key components.

• Oil Compatibility: The refrigerant is compatible with mineral (MO), alkylbenzene (AB) and synthetic (PAG/POE) oils typically used in R12, R134a and HFO-1234yf air conditioning systems. This eliminates the need for an expensive and complex oil change before charging.

• Installation: The 12a-YF Duracool is designed to be charged directly after emptying the previous fluorinated gas circuit. It can be used with standard loading equipment and refrigeration hoses for professionals (fittings adapted to the cylinder thread).

Use and Implementation by Professionals

This 5.44 kg cylinder is intended for professionals in automotive air conditioning (Clim Auto), refrigerated transport or refrigeration requiring a large volume for regular use.

Key Instructions for Charging:

• Conversion Ratio: It is imperative to use the specified conversion ratio: 1 kg of Duracool 12a-YF replaces approximately 2.08 kg of HFO-1234yf.

• Tool needed: Charging should be performed by a qualified technician, using a suitable manifold and charging hose .

• Security: As hydrocarbons are flammable, strict safety procedures for handling flammable refrigerants must be followed (adequate ventilation, extinguishing of ignition sources).

The 12a-YF Duracool is the ideal substitute for a fast, cost-effective and environmentally friendly transition to cleaner and more efficient air conditioning operation.

Detailed technical specifications